Sandwiched structure of hot-deformed Nd-Fe-B permanent magnets processed by Nd-Cu eutectic alloys diffusion

A series of sandwiched structures with different near-surface mass fractions x(x=3 wt%,4 wt%,5 wt%)was employed to develop high-coercivity hot-deformed Nd-Fe-B magnets by the addition of 2 wt%Nd-Cu eutectic alloys via adjusting the middle thickness and near-surface thickness.The designed magnet with a pronounced composite structure shows a 23% increase in coercivity with a 6% loss of remanence by adjusting the sandwiched structure at 4 wt% Nd-Cu eutectic alloys in the near-surface regions.The results indicate that the near-surface Nd-Cu-rich "shell" structure can effectively suppress the magnetization reversal of overall magnets,enhancing the coercivity.With the help of loading stress,Nd-Cu liquid enriched at the near-surface regions of the sample is infiltrated into the Nd-Cu-lean middle region,resulting in a concentration gradient.Microstructure characterizations further demonstrate that the infiltrated Nd-Cu eutectic plays a critical role in inhibiting grain growth and intergranular magnetic interaction.The optimized microstructure features suppress the reversed magnetization process,which makes a positive contribution to coercivity.     

Pressure-induced transparency of MgO,Al2O3, AlN,and cBN ceramics at room temperature

The in situ axial X-ray diffraction patterns of four ceramic powder samples (MgO, Al₂O₃, AlN, and cBN) that were compressed in a diamond anvil cell under uniaxial non-hydrostatic conditions were recorded. The microscopic deviatoric stress as a function of the pressure was determined from the X-ray diffraction peak broadening analysis: the curves increased approximately linearly with the pressure at the initial compression stage and then levelled off under further compression. Pressure-induced transparency was observed in all of the samples under compression, and the pressure at the turning point on the curves of the microscopic deviatoric stress versus pressure corresponded to the pressure at which the samples became transparent. Analysis of the microstructural features of the pressure-induced transparent samples indicated that the compression caused the grains to fracture, and the broken grains bonded with each other. We demonstrated that the ceramics’ pressure-induced transparency was a process during which the grains were squeezed and broken, the pores were close between the grains, and the broken grains were re-bonded under compression.     

Oxidation and ablation behaviour of multiphase ultra-high-temperature ceramic Ta0·5Zr0·5B2–Si–SiC protective coating for graphite

To provide reliable oxidation protection for carbon materials under harsh high-temperature aerobic environments, a dense monolayer-multiphase ultra-high-temperature ceramic Ta_0·5Zr_0·5B₂–Si–SiC (TZSS) coating was fabricated by a combination of dipping and in-situ reaction. The oxidation resistance of the TZSS coating was investigated at 1923 K in air. The results indicated that the TZSS coating could offer at least 70 h of oxidation protection for the matrix material. The synergistic oxygen-blocking effect of the thick oxide layer formed during the oxidation test and the inner coating, played a key role in the oxidation protection process. These were responsible for the excellent oxidation resistance ability of the TZSS coating. Additionally, the ablation performance of the TZSS coating was also investigated under increased heat flux from 2.4 MW/m² to 4.2 MW/m². The ablation behaviours changed from the oxidation and evaporation of coating materials to mechanical scouring, corresponding to increased mass and linear ablation rates. Interestingly, after ablation for 40 s under a heat flux of 4.2 MW/m², a new microstructure composed of “lath-like” Ta₄Zr₁₁O₃₂ solid solution grains was found in the ablation center. This oxide layer possessed few micropores, which could provide reliable protection for the matrix material under ultra-high-temperature oxygen-containing airflow erosion, thus preventing further damage to the composite.     

Review of hydrogen crossover through the polymer electrolyte membrane

Proton exchange membrane fuel cell (PEMFC) is considered to be a promising, clean, and efficient energy conversion device. At present, the main challenges faced by the application of PEMFC in the automotive are cost and durability. Hydrogen from anode to the cathode through polymer electrolyte membrane (i.e. crossover hydrogen) affects the durability of fuel cells. In this paper, the existing literature on hydrogen crossover is reviewed and summarized from consequences, causes, mitigation measures, and detection methods. The influences of hydrogen crossover on the components and performance are discussed. The causes are analyzed from structural permeation and membrane degradation. The methods of alleviating the degradation of the membrane are summarized. The electrochemical and non-electrochemical monitoring methods are described, and the segmented current method is explained separately. The existing problems and research prospects are put forward, which lays a foundation for further research on hydrogen crossover and improvement fuel cell durability.     

Comprehending the role of the S-phase on the corrosion behavior of austenitic stainless steel exposed to H2S/CO2-saturated liquid and vapor environments

The corrosion behavior of austenitic stainless steel after low-temperature liquid oxy-nitriding (LON) was investigated by exposing in H₂S/CO₂-saturated liquid and vapor environments up to 720 h at 60 °C. The corrosion rates before and after LON were compared by the weightlessness method, and the microstructure as well as the corrosion scales were characterized using surface analysis methods. The results indicated that the composite S-phase layer with the outer Fe₃O₄ layer and the inner nitrogen-rich sublayer could improve the corrosion performance in H₂S/CO₂-saturated environment. The base material (BM) suffered local corrosion first, which then transformed into uniform corrosion. As a comparison, The LON sample, covered with a thin corrosion product layer, indicated slight local corrosion. The excellent corrosion resistance of the S-phase should be attributed to the blocking effect of the continuous Fe₃O₄ film as well as the suppression of the atomic mobility by the nitrogen-containing supersaturated solid solution.     

Adaptive constraint control for flexible manipulator systems modeled by partial differential equations with dead-zone input

In this article, based on partial differential equations (PDEs), the flexible manipulator system with both dead-zone input and state constraints is studied. The dynamic model of the flexible manipulator system is described by PDEs. The parameters of the dead-zone input are unknown, and the state constraint problem is also considered. An adaptive approach is proposed to offset the effects caused by dead-zone input. Thus, to guarantee that all states remain within their respective constraint regions, the boundary control law based on the barrier Lyapunov function is given, and an adaptive controller is designed. According to the Lyapunov analysis method, the control method is given to ensure that all signals of the closed-loop system are bounded and all states satisfy the constraint conditions. Finally, simulation results show the effectiveness of the proposed control method in this article.     

Uplink Low Power Based Radio Resource Management in Wireless Heterogeneous Networks

Wireless Personal Communications - Due to the rapid rise of energy consumption and limited battery power of wireless user equipment (UE), low power communication becomes very important....